Floorbox square 300
BOX-SQ-260-300
Floorbox square 300
BOX-SQ-260-300
Fitted with the pre-installed levelling tube and cover plate
Tube material: PA6 reinforced fibre glass, flame retardant
Heights: 28 - 38mm
Measurements: 318 x 318mm
Cover thickness: 1,25mm
Base plate thickness: 1mm
Application: recessed floors with screed
SKU | Article code | Finishing | Dimension A | Packaging | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|
|
17243 |
FS-BOX28-SQ-260-300-PG |
PG
|
28
|
1
|
Default
|
|
||||
Workload
Additional information
Finishing
Sendzimir galvanized (EN 10143) PG (pre-galvanized):
Products made of Sendzimir (pre-galvanized) or continuous hot-dip galvanized steel sheet and coils are mostly used wherever limited chemical contamination is likely, for example, in of ces, industrial buildings, covered parking lots, etc. Characteristic of this steel type is that – prior to mechanical deformation – it is given a zinc coating by means of a continuous dipping process. This zinc coating is easily deformed. A cathodic action occurs on cut surfaces (up to 1.5mm) that protects against oxidation. First, the steel is chemical cleaned and roughened in order to achieve a good bond. After the dipping process, the surplus zinc is blown off and one obtains an extra passivating coat (an ultra-thin protective coat) to prevent oxidation of the zinc coating (white rust). The coating thickness is usually expressed in g/m2. The most deployed type of Sendzimir steel is Z 275 = 275g/m2 (weighed on both sides), this corresponds to 18-20 µm (micron). Sendzimir galvanized steel sourced from modern galvanizing lines has, in general, a uniform, shiny appearance. The previous, common fl owery surface is scarcely seen these days. This effect is obtained under the infl uence of lead but has no eff ect on the quality of the coating. The use of lead was banned due to the ever more stringent environmental standards. |
|||||||||||
|
17244 |
FS-BOX38-SQ-260-300-PG |
PG
|
38
|
1
|
Default
|
|
||||
Workload
Additional information
Finishing
Sendzimir galvanized (EN 10143) PG (pre-galvanized):
Products made of Sendzimir (pre-galvanized) or continuous hot-dip galvanized steel sheet and coils are mostly used wherever limited chemical contamination is likely, for example, in of ces, industrial buildings, covered parking lots, etc. Characteristic of this steel type is that – prior to mechanical deformation – it is given a zinc coating by means of a continuous dipping process. This zinc coating is easily deformed. A cathodic action occurs on cut surfaces (up to 1.5mm) that protects against oxidation. First, the steel is chemical cleaned and roughened in order to achieve a good bond. After the dipping process, the surplus zinc is blown off and one obtains an extra passivating coat (an ultra-thin protective coat) to prevent oxidation of the zinc coating (white rust). The coating thickness is usually expressed in g/m2. The most deployed type of Sendzimir steel is Z 275 = 275g/m2 (weighed on both sides), this corresponds to 18-20 µm (micron). Sendzimir galvanized steel sourced from modern galvanizing lines has, in general, a uniform, shiny appearance. The previous, common fl owery surface is scarcely seen these days. This effect is obtained under the infl uence of lead but has no eff ect on the quality of the coating. The use of lead was banned due to the ever more stringent environmental standards. |
EN50085 compliant
Fitted with knockouts for use with flexible tubing
- FS-BOX28: dia 16 - 21mm
- FS-BOX38: dia 16 - 25mm
Not suitable for floor ducts
Plug & Play system (no extra assembly of components required)
Height can be adjusted through post-levelling once the screed has dried out
Earth terminal fitted in base plate
Alignment provisions in base plate
- FS-BOX28
Standard screed height = 66 - 100 mm
Greater levelling range available on request
- FS-BOX38
Standard screed height = 76 - 110 mm
Greater levelling range available on request
No results
No results were found for your current search